How to enable Magni-Plus AES feature?

Your the AES default of Magni-Plus HBA is disabled. You should use MDU to enable it. 

Use MDU tool under tools folder, 
  1. edit 9200.txt. 
     Change
	[AES]=DISABLE

     to 
	[AES]=ENABLE
     Save and exit.	
  2. Execute MDU.exe usage >mdu restore_cfg -f 9200.txt
#################################################################################

How to enable Magni-plus intelligent rebuilding feature?

"Intelligent rebuilding feature" default is disabled. You should use MDU to enable it. 

Use MDU tool under tools folder, 
  1. edit 9200.txt. 
     Change
	[INTELLIGENT]=DISABLE

     to 
	[INTELLIGENT]=ENABLE
     Save and exit.	
  2. Execute MDU.exe usage >mdu restore_cfg -f 9200.txt
#################################################################################

How to enable Magni-plus Firmware to control GPIO LED?

"Controling GPIO LED feature" default is disabled. You should use MDU to enable it. 

Use MDU tool under tools folder, 
  1. edit 9200.txt. 
     Change
	[CTL_GPIO_LED]=DISABLE

     to 
	[CTL_GPIO_LED]=ENABLE
     Save and exit.	
  2. Execute MDU.exe usage >mdu restore_cfg -f 9200.txt
#################################################################################

How to enable Magni-plus Firmware to HyperDuo Hybird mode?

"New HyperDuo Hybird mode feature" default is disabled. You should use MDU to enable it. 

Use MDU tool under tools folder, 
  1. edit 9200.txt. 
     Change
	[HYPERDUO_HYBRID]=DISABLE

     to 
	[HYPERDUO_HYBRID]=ENABLE
     Save and exit.	
  2. Execute MDU.exe usage >mdu restore_cfg -f 9200.txt
#################################################################################
How to PHY Tuning Page?

"[Px_PHY_TUNNING_1]=FFFFFFFF" default is FFFFFFFF. Unless this value(FFFFFFFF), others 
  will be set into registers(Generation x Setting y). You should use MDU to enable it. 

[P0_PHY_TUNNING_1]=Port0=>"Generation 1 Setting 1(High 16 bits)" : "Generation 1 Setting 0(Low 16 bits)"
[P1_PHY_TUNNING_1]=Port1=>"Generation 1 Setting 1(High 16 bits)" : "Generation 1 Setting 0(Low 16 bits)"
[P0_PHY_TUNNING_2]=Port0=>"Generation 2 Setting 1(High 16 bits)" : "Generation 2 Setting 0(Low 16 bits)"
[P1_PHY_TUNNING_2]=Port1=>"Generation 2 Setting 1(High 16 bits)" : "Generation 2 Setting 0(Low 16 bits)"
[P0_PHY_TUNNING_3]=Port0=>"Generation 3 Setting 1(High 16 bits)" : "Generation 3 Setting 0(Low 16 bits)"
[P1_PHY_TUNNING_3]=Port1=>"Generation 3 Setting 1(High 16 bits)" : "Generation 3 Setting 0(Low 16 bits)"


Use MDU tool under tools folder, 
  1. edit 9200.txt. 
     Change
	[P0_PHY_TUNNING_1]=FFFFFFFF
	[P1_PHY_TUNNING_1]=FFFFFFFF
	[P0_PHY_TUNNING_2]=FFFFFFFF
	[P1_PHY_TUNNING_2]=FFFFFFFF
	[P0_PHY_TUNNING_3]=FFFFFFFF
	[P1_PHY_TUNNING_3]=FFFFFFFF

     to 
	[P0_PHY_TUNNING_1]=XXXXXXXX
	[P1_PHY_TUNNING_1]=XXXXXXXX
	[P0_PHY_TUNNING_2]=XXXXXXXX
	[P1_PHY_TUNNING_2]=XXXXXXXX
	[P0_PHY_TUNNING_3]=XXXXXXXX
	[P1_PHY_TUNNING_3]=XXXXXXXX
     Save and exit.	
  2. Execute MDU.exe usage >mdu restore_cfg -f 9200.txt